Installation Instructions REPLACING AN EXISTING UNIT? Replacing a ducted unit Check the “Essential Elements” label for New ducted installation: important information. For personal safety, this Zoneline must be.IMPORTANT – Observe all governing codes and ordinances.
#How to install peltor arc rail adapter code
Follow the National Electrical Code (NEC) or local.IMPORTANT – Save these instructions for CAUTION: local inspector’s use.Installation Zoneline Air Instructions Conditioners Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: IMPORTANT ELECTRICAL BEFORE YOU BEGIN Read these instructions completely and carefully. To replace the air filters: Keeping these f Clogged filters reduce cooling, heating and air flow. The most important thing you can do to maintain the Zoneline is to clean the filter at least every 30 days. Air Filters To remove the air filters: FRONT FRONT 2 Air filters Pull up Dirty filter-Needs cleaning Clogged filter-Greatly reduces cooling, heating and airflow. To maintain optimum performance, clean the filters at least every 30 days. If they are clogged with dirt or soot, they may be professionally steam cleaned. Outdoor Coils The coils on the outdoor side of the Zoneline should be checked regularly. Some commercial cleaners may damage the plastic parts. Room Cabinet and Case Turn the Zoneline off and disconnect the To clean, use water and a mild detergent. Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support Care and cleaning. A separate wire pair must be run from each separate controlling switch to each individual Zoneline. Central Desk Control When connected, the unit can be turned ON or OFF with a switch located at the Central Control Panel. Connections provide 24 V AC to energize a remote relay, turning on the external fan. External Fan (Obtained locally) When connected, an auxiliary or external fan can be controlled with the indoor fan motor on the Zoneline. This increases the fan speĪuxiliary controls on your Zoneline. If the unit is ducted, the Duct Mode the display. Pressing MODE on Model AZ4100 will This setting is used when the unit is installed using a return you to AUX SET mode and an “AU” will appear in duct adapter kit. For Model AZ6100, press MODE to continue setting other functions. Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support MODE 7 Duct Mode The default setting for Mode 7 is OFF. Press the down LOW FAN arrow for OFF " " or the The HIGH COOL HEAT LED light on the main control will be on. Press MODE again to change to the Heat Sentinel. The COOL LED light on the main control Freeze Sentinel OFF will be on. LOW FAN Press MODE until a 3 appears in the first digit of the display for AUTO HEAT Freeze Sentinel mode. Freeze Sentinel/Heat Sentinel MODE 3 HIGH COOL In the default setting for Mode 3, Heat Sentinel is off, Freeze Sentinel is on. There are 9 different modesĪuxiliary controls on your Zoneline. The owner is responsible for ensuring the auxiliary controls are set to the desired function. See the To Remove the Room Cabinet section. Auxiliary Set Button Auxiliary Controls-Aux Set Button The auxiliary set controls are located behind the room cabinet, below the control panel. Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support Auxiliary controls on your Zoneline. When set at the closed position, only the air inside the room is circulated and filter The ventilation control lever is located at the middle left side of the Zoneline unit, behind the room cabinet. If you do not plan to use the ventilation feature, leave these two screws in place. See the Installation Instructions in the back of this manual. Closed Ventilation Control Open position position NOTE: Two shipping screws must be removed from the vent door before use. When set at AUTO, and off to keep the room at the same level it automatically switches between LOW of comfor The compressor will cycle on LOW or AUTO speed. TEMP CONTROL FAN, MODE & SLEEP OPERATION Controls Temp Control Fan, Mode and Operation Control The temp control is used to maintain the room FAN-Sets the fan operation for HIGH, temperature. Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support About the controls on your Zoneline. SAFETY PRECAUTIONS This Zoneline must be properly installed These R410A air conditioning systems in accordance with the Installation require contractors and technicians to Instructions before it is used.
#How to install peltor arc rail adapter manual
WARNING! For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. 4 Español For a Spanish version of this Care and Cle 4 Heat/Cool Model 4100 Auxiliary Controls. 2 Owner’s Manual and Installation Instructions Operating Instructions Air Direction.
0 kommentar(er)
